4' Drag-On™ Float
Part# 2302
$ 108.45 |
100% Foamless Recyclable Float
• Rotationally Molded Polyethylene
• Dimensions: 24" x 48" x 10"
• 3/16" Nominal Wall Thickness
• Buoyancy 400 Lbs.
Float features conduit channels molded into the top of the float, and skid board channels molded into the bottom. |
Lag Bolt Kit
Part# 9275-6
$ 3.82 |
6 each - 3/8" x 2½" Galvanized lag bolts,
⅜" washers and ½" washers.
For attaching the 4' Drag-On float to a wood frame dock. |
3' Drag-On™ Float
Part# 2301
$ 89.79 |
100% Foamless Recyclable Float
• Rotationally Molded Polyethylene
• Dimensions: 24" x 36" x 10"
• 3/16" Nominal Wall Thickness
• Buoyancy 300 Lbs.
Float features conduit channels molded into the top of the float, and skid board channels molded into the bottom. |
Lag Bolt Kit
Part# 9275-4
$ 2.60 |
4 each - 3/8" x 2½" Galvanized lag bolts,
⅜" washers and ½" washers.
For attaching the 3' Drag-On float to a wood frame dock. |
3' Cell-O-Foam Float
Part# 2304
$ 91.43 |
24"x36"x12" Foam Filled Float
Buoyancy 327 Lbs. |
4' Cell-O-Foam Float
Part# 2305
$ 100.70 |
24"x48"x12" Foam Filled Float
Buoyancy 434 Lbs. |
Lag Bolt Kit
Part# 9278-6
$ 5.45 |
6 each - 3/8" x 4" Galvanized lag bolts,
⅜" washers and ½" washers.
For attaching a Foam Filled Float to a wood frame dock. |
90º Corner Iron
Part# 6027A
$ 5.00 |
1/4" Steel Corner Stiffener.
4" H x 4⅝" W x 4⅝" W.
3½" from inside corner to hole.
Holes are 2½" apart, center to center. |
Keyhole Anchor Plate
Part# 6013A
$ 15.00 |
Adjustable chain holder for floating docks only. Swim floats can use this but need a swivel in the chain so the float can spin without shortening the chain. If chain gets too short from twisting, the anchor will lift up. If used on a floating dock, use two plates and cross the chains as you would on a trailer hitch to minimize swaying. Chains should be atleast twice the water depth in length. |
Reinforced Hinge Plate
Part# 6010
$ 19.45 |
Hinge for joining corner to corner. This plate reinforces the frame on the corner. Uses 6 - 3/8" x 2½" Galvanized Carriage Bolts for mounting. |
Reinforced "T" Hinge Plate
Part# 6011
$ 28.00 |
Use this Hinge when a dock section meets into side of dock at the hinge. |
"T" Hinge Plate
Part# 6008
$ 13.80 |
Used to join a floating dock to the side of another. (For example, a place where a ramp meets a larger platform and connects to the side rather than the corner.) These are not sold as a pair. One side of the ramp may meet a corner of another section making an L-shape so you would use the reinforced hinge plate on the outside edge of the L-shape and one T-hinge on the inside of the L. To join a ramp to a float as an L-shape you need a total of 3 reinforced hinge plates and one T-hinge plate. If you want to make a T-shape connection instead, you would use a total of 2 reinforced hinge plates and 2 T-hinge plates. Corner irons and blocking between stringers near T-hinges will help reinforce the outside stringer. |
45º Finger Plate
Part# 6009
$ 26.65 |
Hinge for when you build a 45º frame. •Provides more stability •Often used in boat slips to allow you to reach under the bow of the boat when docking. |
Long "L" Hinge Plate
Part# 6012
$ 14.75 |
Long L Hinge Plate |
Short "L" Hinge Plate
Part# 6007
$ 13.65 |
Short L Hinge Plate |
Straight Hinge Plate
Part# 6006
$ 12.75 |
Hinge connector plate used to join two floating dock sections. Suggest using a 90º corner iron to reinforce corner where straight hinge plate is used. |
Shore Anchor Bracket
Part# 6014
$ 19.30 |
Used to anchor your floating dock system to the shoreline.
Each anchor bracket uses a piece of 1½" Schedule 40 pipe to be driven into the ground.
(Pipe Sold Separately) |
Post Guide
Part# 6097
$ 16.15 |
Guide for 2" Galvanized Pipe. This works best in shallow water. If water level changes, Pipe may need to be moved. Keep on side away from boat. Some installations may require anchors with chain. Inner Diameter is 2 7/8". |
Hinge Bolt W/ Nylock Nut
Part# 9092
$ 2.10 |
For connecting hinge plates together.
Bolt is 3/4" diameter x 1¾" long. |
45º Finger Stiffener Plate
Part# 6004
$ 9.90 |
Boat slips often have a 45º shape that fits around the bow of the boat. This plate reinforces the frame at the 45º. |
Pipe Safety Caps
Part# 2278G
$ 2.15 |
Place over top of pipe to
protect from sharp edges.
Fits 1⅞" OD Pipe. |
6" Galvanized Cleat
Part# 2256
$ 2.15 |
6" Galvanized Cleat |
8" Galvanized Cleat
Part# 2258
$ 5.25 |
8" galvanized cleat (Also available with cleat stiffener). |
10" Galvanized Cleat
Part# 2259
$ 9.35 |
10" galvanized dock cleat. |
Cleat Stiffener
Part# 6060
$ 6.45 |
The cleat stiffener bolts underneath deck boards and to the side stringer for reinforcing the cleat.
Made from extruded, marine grade aluminum angle.
Mounting bolts are sold separately. |
8" Cleat Bolt Kit
Part# 9262
$ 2.25 |
For attaching the 8" galvanized cleat to the cleat stiffener when using standard decking. |
10" Cleat Bolt Kit
Part# 9263
$ 2.38 |
For attaching the 10" galvanized cleat to the cleat stiffener when using standard decking. |
8" Cleat w/ Stiffener
Part# 9258A
$ 11.75 |
8" Galvanized Cleat is bolted through the decking to an aluminum cleat stiffener which is bolted to the dock frame.
Bolt kit (9262) sold separately. |
10" Cleat w/ Stiffener
Part# 9259A
$ 16.05 |
10" Galvanized Cleat is bolted through the decking to an aluminum cleat stiffener which is bolted to the dock frame.
Bolt kit (9263) sold separately. |
Nylon Cleat
Part# 2257
$ 3.95 |
8" Nylon Cleat |
Folding Cleat
Part# 2275
$ 24.50 |
Plastic folding cleat so you don't stub your toe. |
Rigid Float Connector Kit
Part# 9175K
$ 151.55 |
Join two floating sections together with this hinge to make them rigid at the connection. If joining more than two sections, use the Reinforced Hinge Plate instead to allow some flexibility between sections. This image only shows one side of the dock. The kit includes two more hinges for the side not shown. Attach a male and female on each section in order for them to line up. Do not put two males on a section and two females on the other. |
280lb. Concrete Anchor
Part# 9029
$ 54.00 |
280 lb. Concrete Block Anchor with Galvanized Anchor Rod |
Concrete Anchor Rod
Part# 6029
$ 15.50 |
Concrete Anchor Rod |
5/16" Shackle
Part# 2203
$ 2.15 |
Use to connect chain to anchors,
buoys, or other chain.
¾ Ton Working Load Limit. |
3/8" Shackle
Part# 2204
$ 2.70 |
Use to connect chain to anchors,
buoys, or other chain.
One Ton Working Load Limit. |
1/2" Shackle
Part# 2206
$ 4.50 |
Use to connect chain to anchors,
buoys, or other chain.
Two Ton Working Load Limit. |
5/16" Eye-Eye Swivel
Part# 2210A
$ 7.95 |
Use inline with floating swim raft
anchor chain to keep chain from
becoming twisted. |
3/8" Eye-Eye Swivel
Part# 2209
$ 9.75 |
Use inline with floating swim raft
anchor chain to keep chain from
becoming twisted. |
1/2" Eye-Eye Swivel
Part# 2210
$ 13.50 |
Use inline with floating swim raft
anchor chain to keep chain from
becoming twisted. |
5/8" Eye-Eye Swivel
Part# 2211
$ 14.25 |
Use inline with floating swim raft
anchor chain to keep chain from
becoming twisted. |
5/16" Galvanized Chain
Part# 1267
$ 2.90 /foot |
This Price is per foot. This chain doesn't last as long as 3/8" chain does in the water. *Maximum 150 lbs. per box We recomend twice the water depth in length. If chain is too short, the anchor can get moved as chain jerks from wind or waves. Spinning will shorten chain unless you use a swivel. |
3/8" Galvanized Chain
Part# 1268
$ 3.90 /foot |
Our most popular size, used for most residential applications.
We recomend twice the water depth for chain length. If chain is too short, the anchor can get moved as chain jerks from wind or waves. |
1/2" Galvanized Chain
Part# 1268A
$ 5.70 /foot |
This price is per foot. 1/2" chain is hard to cut yourself unless you have the proper tools. *Maximum 150 lbs. per box We recomend twice the water depth in length. If chain is too short, the anchor can get moved as chain jerks from wind or waves. Spinning will shorten chain unless you install a swivel. |
